Search results

I just leave a message to the seller that I'll leave positive when it arrives and all my info is current. Most sellers do robot reply feedback the minute they get your money anyway. I've got one guy that I need to drop the hammer on because he sold me Japanese projector headlights for my sisters...

Ours isn't doing anything like that so probably just a light load tripping out the motor balance detection stuff. We just did a huge deep wash whites load with aprons and towels. It claimed 99 minutes and never tripped the code once. Well if anyone needs to do the bearings in one of these I...

Well they are all in place and nothing looks broken so I think we'll watch it and see how it does. I don't think they are expensive but if they aren't bad no reason to spend the money. I looked over the manual for the self tests and doesn't appear to be any relearning functions but for a...

Self test mode? Thanks, found the manual and it says the pump can make noises as it sucks in air but it appears to be working so guess as long as it doesn't get super loud we'll live with it. Have noticed it seems to throw a uL code a lot but it either balances again on its own or stops till...

First load good. Well got a brand new braided hose at Ace down the street today after work, sister ran a big load of jeans and no leaks underneath, from the new hose, or the patch on the tub. It runs quiet except for the I'm pretty sure drain pump. It growls and seems to make a bearing noise...

Well ran a water only short cycle and it works fine, no leaks from the motor area and quiet again except for I'm pretty sure the pump that drains the tub kinda growling, sister says it's always made noises when draining. I didn't see any problems in the outer tub patch but the cold water hose...

Redone today with pics. Well gathered back up my tools and tore it back down today to do a postmortem and replace all the parts again. I took a TON of pics to document what I found and did. Unfortunately I got a bit too crazy with the dead blow shot mallet and the shaft flew out hard and...

OK, the new kit arrived today at 7pm. I took pics of the original shaft as it came out after running since 2014. The newest kit that arrived today assembled that came in a Whirlpool box, and the last 1 month old Chinese replacement is still in the machine so pics will have to wait till I tear...

New oem whirlpool parts here tomorrow Well got notification that my new Whirlpool rebuild kit will be here tomorrow 5/24 so soon will have to tear it back down and see what exactly failed and wasn't in place like it should have been. Funny thing is the weird shaft squeal went away again and...

Kit bit the dust Well got home early this week and it was squeaking badly from around the shaft and was leaking enough to leave a few small puddles, plus very faint but obvious bearing noise already so going to have to replace the bearings yet again. Obviously the seal needed to be seated all...

yeah, it's 110 etc. It's on the lid and a few other places but when I got it as a refurb back in 2014 many users here had one or were aware of it just by the top load HE 28102 model. Too bad the seal and bearing design are so fragile as otherwise it's a great machine and has saved us a lot on...

Well, she ran another full water load and it appeared to leave a few dirty dried up drops on the drip pan but it was dry underneath when I checked after work. It's usable and mostly doesn't leak now and at least I have the tools now so I can replace the seal and bearings easily enough if it...

It mostly dripped a few drops as we ran a high water wash. Today we are running normal loads with a low drip pan under it and it's so far completely dry. I was like you, didn't really want to tear it completely down as it's a lot more involved then I'm used too. I don't think any of our old...

Finally replaced everything Well did it over last weekend finally and test drove it last night. It worked very quiet and smoothly again but it was leaking a tiny bit and I remember I couldn't get the seal completely flush but I greased it up good and put plenty of the silicone seal on the...

Top load HE I don't think I made it clear this is one of the Whirlpool Maytag direct drive units known for early tub bearing failures due to moisture making its way down the shaft and into the bearings till they rust up and fail. I got it in 2014 and by about 2016 17 it started getting slightly...

Well guys I finally tore down the 28102 I got in 2014 because the tub bearings were shot and very noisy and it finally started leaking. I got the full new shaft, bearings, and install tool. I started tearing it down Saturday, had to do other things and finished it Sunday. I am pretty sure both...

Picking berries for TV I picked berries every summer from 6th grade through high school and got pretty fast at it towards the end. We usually made 5 or 6 a day and at the end I could make 20 25 a day. I paid 115 bucks for that Zenith because it was damaged in the cabinet and they took it in...

1953 Zenith TV Had a 53? Zenith 23" TV with a AM radio and a slide out cobra Matic turntable given to me when I was a kid. It was ancient even then and picture tube was so weak it was hard to see in the light and very fuzzy, plus the picture was cut off on the bottom and right side but it...

Neon I have the sohc version but 95 only in that engine got a hotter cam so it has about 136hp with better low end than the Dohc version. It was designed to beat the Honda civic that year and had at least 15 or more hp so they were successful but Daimler also cheapened out the parts and one was...

. My 95 Neon did the same idle down to nothing at a stop sign. Automatic and all that and it would just keep dropping rpm and die. I had to two foot it and pop it in neutral if it did it and restart it while rolling to a stop. On mine it was the EGR valve I think sticking open and leaning...