Search results

Take some photos of the control boards. The answer may be right there. I found a document but they never have pcb level details. http://docshare04.docshare.tips/files/22599/225997012.pdf

its leaking in the washer? Any photos of where it is leaking exactly? It can be taken apart and greased. Was it this machine that had leak issues with the rubber part which connects the dispenser to the tub (Underneath).

I have a smaller bag of that It seems less concentrated than the local Unilever Persil. This Henkel Persil requires more powder per wash according to the instructions but I may use half the amount as from memory it was quite foamy in rinsing. Good luck with your powder.

The cons of having a professional machine. Having owed a PW5065 machine, they are loud. Every squeak and rattle etc is multiplied in that empty shell. Not one bit of sound proofing. To me it sounds like My W5873 when there is one item inside. My W5873 is quiet when it is fully loaded and I...

Limited answers 1) ??? The machine has a board in the front and the main board which you will be replacing. If you need programming of spin-speeds etc then YouTube can help. 2) The rast plugs only go into one connector (hopefully). It pays to label with a marker pen or to take detailed photos...

String excitation mode! How much did that beauty set you back? Good luck it getting it to work. Perhaps a video of it in action is called for? Rich

Further question When you do manage to turn it on, do all of the LED's have the same degree of brightness? I have found some of the LED's were faulty and have replaced them. These are the LED's around the dial. The machine I have wouldn't turn on. When the chip was replaced it worked...

If its like my machine which is a W5740 Miele, there is a PCB under the lid with the label ELP 165-s I bought mine for an absolute bargain because it had power issues. There seems to be issues with the power chip TNY278GN. I was lucky that I replaced mine and it then worked flawlessly...

Arg, and now I cannot edit my grammatical error without upgrading.

A questions to clarify please Is it a W5847 or is it a W5801? Does it have a regular brushed motor or does it have a brushless motor?

Congratulations, lovely machine But do you worry about mould. I have a CM6150 and I'm forever looking inside where possible. If only they had a UV light on the inside or a fan to dry it out after the steaming.

The aeg bearing holder in green requires an odd tool to remove or you need to be creative using other tools in order to spin it off. I agree that its so sad that AEG in the past made magnificent appliances. I wonder if the engineers moved to Miele?

If you slip the belt off And spin the drum pulley can you hear the sound more clearly? Youtube has a couple of videos. A quick google of "aeg toplader bearing" brought some up. It looks to be a fun project.

They have combined The turbidity sensor with the NTC.

Looking at a WTH service document There are a few components which use 13v on the WTH washer dryer. But this is a very interesting post. I wonder if the tech will find the source or just scrap the lot. Keep the info coming please. Cheers Rich

In the photo above The right most set of plugs has two plugs. According to the wiring diagram you need the pcb which supports 3 plugs and not 2. EL200-A. I too have an EL200-C and it has two silver traces where the plugs would go and it is missing a relay too. Here is an ebay listing for the...

Do you hear the clicking of the water diverter moving? Or can you get the machine to spin on a spin only cycle?

Any good? This website has many Miele models but perhaps this W900 can help? https://haztartasigepszervizes.hu/mosogep/MIELE/btd_f_f/11/typ_btd/0360/W900SPECIAL/index.html

its held on by one screw/bolt under the seal, two torx screws in the bottom corners (remove the lower plastic trim). The top part is held in by plastic pins. I would check the feet are level, the rubber on the feet is intact and the locking nut for each foot is locked tight...

Pw5065 Similar machine, same problem. This is 10+ years old. Different design but aluminium alloy with a stainless steel spindle.