Search results

Yup the unit has a slight rearward tilt. However, for this pump in a stainless steel tub, the correct water level is reached when the water touches the bottom edge of the element. This is required for proper pressure and circulation. Just saying' :-) L.P.

Actually the water level in the unit appears to be low. The water level after the full fill time should at minimum; touch the bottom of the heating element all the way around. For a 10+ year old machine, the water inlet valve should be evaluated too. L.P.

We've been enjoying them here. They leave a nice light scent. Will repurchase.

A work around for this is to place the pod in a mesh laundry bag or in a nylon knee high stocking......An extra step but it works!

Here ya go........Maytag model: DWU9962AAE. See page 9 regarding service indicators. http://www.maytag.com/digitalassets/MLPDF/Use%20and%20Care%20Guide%20-%206-913551.pdf

I seem to recall a mid 90's T-O-L Maytag offered this as well. Perhaps Drew (Red Carpet Drew) can confirm. L.P.

Here is a well preserved / refreshed Youngstown kitchen in the Buffalo area. See the Zillow link and scroll to the kitchen pics: http://www.zillow.com/homedetails/948-Woodstock-Ave-Tonawanda-NY-14150/30388246_zpid/

Sandy thanks for bringing the American Kitchens documentation back from the past. Back in western NY state there are thousands of post WWII homes built with these cabinets as well as Youngstown. Some are still around. Zillow is a resource for unearthing this sort of thing. By the time the...

Sam you've got a great collection. Say in pic #1, inside the roasting pan, you've got two oblong pans. What size are they? Love the crock pot too. L.P.

Another consideration............is how free flowing the exhaust vent system is. This is a major contributing factor. Have had both and don't recall any significant difference in drying results or time. ..L.P.

I believe this is the latest version of Tide Total Care.....which has worked great in our laundry room. http://www.tide.com/en-US/product/tide-total-care.jspx

Just an observation Brian..........in picture # 6, it appears the lower wash arm is not fully seated on the shaft of the wash arm support. The stainless steel shaft should be flush with the top of the bronze wash arm bearing. This will negatively impact washability. ...L.P.

Noticed the same.........$9.99 for the 100 oz or 92oz @ Kroger.

A few points to clear up regarding: *Whirlpool, Kenmore & Amana dishwashers.....current models are equipped with the single speed filter based wash pump & motor shown earlier. Certain models have alternating wash arms, others operate all spray arms at once *Jennair, certain KitchenAid &...

Think its mid 70's era

The wash motor does in fact run continuously. Any pauses during the wash and rinse periods are determined by the machine control. Additionally, the wash motor powers up very smoothly and does not "chatter". I seem to recall a AW.org member or two, recently installed a machine equipped like...

The picture illustrates the actual wash pump & motor that is used in Whirlpool tall tub dishwashers since 2011. (There is a separate drain pump motor) Certain models operate both wash arms simultaneously. Others have a flow diverter that allows the wash arms to work independently with a...

I believe the service part replaces the 3 piece rubber/vinyl part with a 1 piece plastic tube along with a new upper wash arm bearing. ...L.P.

Glenn it looks like a varistor. Meant to absorb voltage spikes.

Hail storm dings & dents Martin, I had this same thing happen last year to a 2012 Ford Explorer. The hood and the roof had quite a bit of damage. Somehow, the collision shop has a special process using heat lamps. Amazingly, the vehicle upon completion looked showroom new as promised. I...