Search results

This sounds kind of ludicrous, but sometimes I think if machines (mainly top loaders) only had a 8 to 9 pound capacity, you’d be forced to fill the machine all the way up with the smaller capacity tub. Bigger capacity machines aren’t always better, there’s no way I’d be able to use the entire...

Reminds me of a Mark 18 console I translated onto my ‘63 Whirlpool washer, did the same with the dryer as well. They currently reside in my laundry room as I type this.

Final update: got it hooked up to 240v and it works as I would expect. Auto dry feature even works as well to my surprise, will dry to completion depending on the amount of dryness selected.

Haven’t hooked it up to 240v yet, but usually test on 120v to make sure everything is working correctly, if it works on 120v, should work on 240v just fine. Not sure if you noticed, but have two variable pulleys (one on the blower shaft, another on the motor) which I can calibrate and can...

Here’s an update: everything is now completely functional, dryer stops when you open the door, works as intended. The only idiosyncrasy of it is the drum light doesn’t come on in the off position, but comes on when the timer is moved from the off position along with the console light, oh well...

Unfortunately, the 2 speed tumbling feature didn’t work since I couldn’t mount the cable to that tumble speed selector, so I decided to use the ‘speed selector’ to control the heating elements. As for the moisture sensor being grounded through a thermostat, that was the only way to get the auto...

It’s for the 1000 watt element (4600 watts when the 1000 watt element is switched off, 5600 watts when both elements are on), may be a little overboard, but figured it was better to have a contactor switch the element off then using a momentary toggle switch which off the lower wattage element...

This may be overkill, but added a contactor to turn the lower wattage heating element on and off. Could have used a relay, but decided to go the extra mile while I was at it and before I put it back into service next week.

Pat, didn’t you mention in a conversation awhile back that you wanted to get a Whirlpool 29” top filter dryer? Seem to think you did but has been awhile, though.

Could pick them up and sell them for $$$$, or keep them as a back up pair.

Unfortunately, in the later years, they went to a tub seal that was made fairly cheaply which would leak and cold water cycles on top of using too little detergent is what sped up the tub seal’s demise. I believe tub seals could go bad on the older Maytags but have a Maytag 806 from 1979 that...

The tried and true Helical design which has proved itself many times over. Easily one of the most reliable machines in existence, a set of belts and possibly a pump, that’s about it.

Looks like a Dependable Care style of washer judging by the console.

I did check everything earlier this evening, even double checked just to be sure. My guess is the door switch finally gave up the ghost after 43 (were in service from 1963 to 2005, June of 2021 to January of 2023) years of service, can’t really complain about that.

Another update: managed to get the drum light/uv light to come on whenever the machine is running, the idiosyncrasy is it only comes on whenever the timer is moved from the off position but is the only gripe about that. Next, I’ll need to use a contactor to turn the lower wattage element on...

Update: since I bypassed the pulser motor/finish guard, it no longer shuts off when either low/knit and medium/permanent press are selected. Now, onto the door switch and getting the drum light/uv bulb to come on whenever it’s running.

As a start, going to bypass the pulser/finish guard motor. Second, going to look into the door switch situation.

That’s probably what I’m going to have to do. May just end up ‘deleting’ the electronic dry control and finish guard motor, that could be where all the problems lie. Thinking about just using a fan switch to activate the timer motor once it reaches a certain temperature on the auto dry, then...

Did some investigating, turns out the motor wasn’t wired up correctly. John definitely was correct in terms of it will either work or won’t work. Now, the dryer mostly functions in terms of heating up and tumbling, timer advancing. Now here’s the bugs that will have to be worked out: 1. The...

Plugged it in and…nothing. About the only thing that works is the drum light, relay was engaging, but nothing else. Looks like I’ll have to do some digging to see why it’s not wanting to work.