Search results

Hi All: I got a "new" KDS20 to replace my old one that finally rusted out and leaked. It's mint, but the motor bearing squeals. Any suggestions? I can swap the motor from my old one, but are gaskets still available from Hobart? Bobby in Boston

Parting one out! Burnman, What side is it? I will be glad to send you a used corner seal. The manual describes their replacement. Looks like a pain in the neck. Bobby in Boston

HI Steve: Thanks for the response. The drain valve is in the original position, just that the original fill valve was in one straight line- opening, screen, and exit. The new one is at a 90 degree angle, so the solenoid hits the drain valve. No worries. The gasket where the screen is was...

Hello All: I need some help with the replacement of a leaky fill valve for a Superba 20 portable dishwasher. The original part # is D- 240016, and the replacement valve from Whirlpool is #4171000. Problem is, the replacement solenoid and outlet are off to the sides, which impinges on the...

Epicstar: The tube putty looks kind of stiff. Does the two tube mix have better flow? Bobby in Boston (who's really getting sick of washing dishes by hand!)

Hey guys: I went a great old hardware store and found lots of rust treatments and sealers. I picked up some JB Weld Steelstick, steel reinforced epoxy putty. It is designed for repairing rust spots, sealing, heat and acid resistant, and OK for drinking water containers. Has anyone used this...

Hi All: Well, after 33 years of use the KDS 20 has finally sprung a leak due to rust in the sump. Ironically, the rust is on the vertical wall of the sump, about the size of a quarter. It is easy to access. What can be done to seal it? The rust is pretty deep- if I pressed the spot, I know my...

Bobby in Boston says to count him in too. Particulars?

Hi All; Does anyone remember what parts store carries the decal that went on the front panel of the 2007 SQ washers? Also, can anyone guide me to the thread about how to tweek the water level? Thanks! Bobby in Boston

Hi Jon! Don't tempt me. I'm dying to get a SQ pair! Bobby in Boston

Thanks Westie! I tweeked the water level a bit, and it really washes and rinses well. My friend has the Frigidaire with the top console, and I was very impressed with it. I wanted to grab one before they are NLA. I don't particularly care for the new FL's that only use 1 tbs. of water...

All Repaired! Solid plastic legs (GE brand) worked fine, for $4 a piece. A new (used) hinge fixed the misaligned door. It seems the old hinges were all metal- the new ones, at least the one used on this model, have a nylon bushing for the middle section of the hinge. It obviously warped or...

Typical new machinery! Hi John: No luck here either. I think I will try the thick plastic threaded legs and see what happens. Have you ever seen these doors misalign? The bottom is more open than the top, so when it tumbles and clothes hit the glass, it leaks. The glass and door seem OK...

Hi John! It's model #WSXH208A0WW. I have a feeling the door issue is from the glass not lining up with the door frame. I'll reset it and see if it helps. Bobby in Boston

Hi All: I have a new toy: a GE (Frigidaire) front loader, the oldest model with the small porthole door. The plastic hubs that the leveling legs screw into are broken apart. Does anyone have a part#? Also, the door seems to not align with the seal properly. The bottom is a bit more open, so...

Ron,did you make the seller cry???? :-) Bobby in Boston (I'm glad Rich, Chuck and I didn't have to haul that heavy sucker a second time)

Combo: The whine sounds like it is coming from the top of the agitator. It's more of a low pitched squeal. It is consistent with the oscillation of the agitator. Is there a bearing or gasket where the agitator screws onto the shaft? Bobby in Boston

Roto: This one whines too. Sounds like a kitten crying, and the more water that leaves the tub, the louder the whine. When the solenoid releases the brake, the whine stops until the tub is coasting to a stop. Then each slow turn of the tub has a very similar whine. If you have ever seen...

Thanks Roto! I assume this won't do any damage, long term. Full, heavy loads keep the agitator still after most of the water is out and the weight is resting on the fins. Bobby in Boston

Hello All: My Magic Chef/Norge 20 pounder slowly agitates while in the neutral drain. Is this normal? Is there somthing that needs to be adjusted? Do I need to worry about it? Bobby in Boston