Search results

[No message]

[No message]

SCREWED THIS, WRONG PIC OF COURSE :).

Got it home in the rear yard to clean. One of the three knobs on the clock is missing, not sure if it was there before? We looked but nothing.

Ralph I think its going to take 3 of use to get it in the truck bed:( after removing the cast iron parts it was still very heavy. Well built for sure, a solid range. I did notice one chip on the bottom left corner, maybe 5/8 inch but thats a easy fix. Nice amount of grease I had to clean for...

Anti static sheets vs. liquid softner? My moms friend broght some of her liquid softner over to try and she could't stand it cause of the scent or perfume smell. I tried a load and wouldn't use it again. Were back to the static sheets again but just half sheets and thats fine but it amazes me...

OK !!! I'm back :) I've had a bad cold last two weeks so didn't talk to the neighbor with the stove but saw him today getting ready for a yard sale. I asked if he sold the range and no, so asked for a offer, told him I can't pay more than $200 esp because of the safety switch being around $200...

You can also try a used appliance store as they usually have someone repairing in back and usually familiar with older appliances. Have a note ready just incase to give your contact info if they will work after hours.

So thats why? The OSH Store in Van Nuys Ca. was completely redone to a rustic look from floor to ceiling last year or two and the store in Burbank about 7 miles apart folded, I think mostly from slow sales, store was near empty many nights I was there. Went to OSH last night looking for a...

In the first pic, thats not rust, PO stuck masking tape pieces? I dont even remember what the inside looks like and then saw I put two vegie drawers on the top? things stored just too long:(

[No message]

THANKS !!! Thought it would be a bit newer but what do I know? If i get back in there might take a partial pic of top. I think its complete but too much stuff in front of it to move any time soon. BTW a typo, i paid closer to $40 i think. My original thought back then was to use it in a rental...

I found my drill bits in garage but looked and saw the old Frige I bought years ago from a thrift store for about $20 and is a Frigidaire? Didn't have the camera but emblem said frigidaire and there was a thin trim across the front about a foot down from the round top. It has a handel like a...

NICE FRIGE ;) Usually theres an exsisting screw on the frame pretty close to attach the ground or might need a short piece of electrical wire to reach with wirenut? I use those eyelet crimp on connectors or solder it to attach with screw if the power cord ground is bare wire at end. Fixing...

I dont know but assume Orchard Supply is owned by Sears as they sell most everything Craftsman? haven't seen them in a market yet. I've bought a couple new Craftsman tools at swap meets, could be stolen I guess? I also dont know of those high end off brands but I like Snap-On, thing is those...

CANT RELATE? No new cars and just Cassettes in my older cars, have tons of them , mostly high quality decks that get up around 18,000hz, cant remember the low end. Was thinking to transfer some to CD's but I better wait for chips or death, things changing too fast for me....mostly listen to AM...

about 4500k a year, live alone and gas stove , heat, wh. do use the microwave and toaster oven quite a bit. many floresent bulbs and small 13" tv. Doesn't matter how much I try to save they just keep hicking the rates so I'll pay more than before...

If you're using that adjustable wrench to work on the motor I'd take it in for repairs :) I do most everything myself from oil change to motor/trans overhaul. Been doing it since I was a teen and like knowing its done right. Mosyly got tired of redoing what so called mechanics failed to do...

MY TRICK ;) I've had problems also with the trigger not rebounding and just not spraying well. I did get mine at a industrial supply but seems like the same cheap quality, I just use it for water but they would always die before I tried this. If the rubber isn't cracked this should work, best...

THINK I GET IT? For propane you dont want the pilot on always and would have to light pilot each time. With the Natural gas the pilot can remain lit and just push the safety valve to light. if pilot goes out would cause main gas not to flow. something like that? Am I close?