Search results

I was confused too Yeah the Glob of Detergent or Fabric softener + Lint and other debris was right in the home position gap. The debris blocked the reflection from the drum so the optical sensor couldn't see the drum rotating. When my dad slipped the piece of junkmail between the sensor module...

Replies #17-19 Fixed the Fault. Somehow a glob of Fabric Softener got onto the drum where the door is and was blocking the optical sensor on the sensor module. My Dad discovered this by slipping a piece of political Junkmail between the sensor module and the drum and the issue occurred again...

Fixed the issue The drum was a little bent and so it would get hot and expand just a millimeter and it was scraping against the front.(not where the metal is or the plastic blower housing, The cover where the moisture sensor wires are, Just barely too.) The back panel was a little bowed in so...

Model GLEQ642AS2

I have recently acquired a stainless steel drum for this machine. It's interchangeable. But today I throw a load of towels in for the first load in a while and it starts making this noise. I think it might be the front glides on the drum and if so I will just put the glides from the other drum...

Reply #2 No. This was tested with clothes. 1 load was towels on high. (proper temperature) 1 was clothes (Normal cycle Mid High temp) 1 was bulky items (Medium temperature, Full size comforter) and 1 was 4 throw blankets. Delicate cycle (Extra low. It felt hotter than 120 Degrees Fahrenheit.

no replies? I am confused. Is nobody reading it?

I recently gave up my LG DLE5977W to make room for this Whirlpool Calypso Dryer. GVW9968KQ2. Serial Number Indicates July of 2003. On Any Cycle chosen It seems to get to max temperature on any temperature except air only then the next heat cycle produces the proper temperature. Do I Have a...

Comforter failure. Tried it in the Neptune TL today The same comforter actually worked in the Maytag Neptune TL.

Lower speeds. Personally on SMALL LOADS ONLY. On my 1989 Kenmore 80 series. I personally put it on delicate wash. On small loads The turnover is just fine. Slow Agitation only sucks on full loads. My Whirlpool World washer. I just select Cottons/Heavy at 14 minutes instead of Cottons/Normal at...

My Dad picked up this piece of junk Bauknecht Whirlpool Duet 2 years ago. We replaced the pump and ran it but it was WAYY TOO LOUD and TOOK FOREVER TO balance a load. We replaced all 4 shock absorbers and that made no difference whatsoever. All it fixed was the noise and sagging. The Sensors on...

reply #2 That's because Fisher&Paykel Machines have high quality seals and they have SKF bearings.

Despite what the collar looks like. It's not rough on my fingers and the seal kit I ordered comes with a 5 year warranty.

2nd try with success so far. I have disassembled the washer and I found that the spider had very little corrosion. I thought that electrolysis would have destroyed it and it would be just hanging in there but nope. The spider is fine. I saw very little buildup when I disassembled the washer. My...

I picked up this set today from a used appliance store, Models GLTF1670AS1/GLEQ642AS2. Dryer is electric. Serial for both states February 2006. The washer's bearings are shot so I am going to disassemble the washer tomorrow. Hopefully the spider shaft isn't too damaged, Otherwise I am going to...

Replies #16 and #7 I have decided to give another a try. I got the matching set. GLTF1670AS1/GLEQ642AS2 Washer's bearings are shot. Hopefully the spider shaft isn't too damaged or I will have to find a donor machine or do a half-### fix and use waterproof bearings from SKF or Timken. Dryer...

I am not and NEVER will wash in cold Except for stuffed animals. I just powder detergent residue sometimes when I clean a machine

I use All Liquid and Snuggle Fabric Softener. Powder seems to eventually get chunky and cake in the machine. I run washer cleaner (Sodium Percarbonate) Once every 1-2 months. I isolated the aluminum spider arm on my LG and I plan to get another Frigidaire Small Door FL washer and give it another...

Bearings and seal are still available as far as I know. Serial starting with 10 or 11 Special 1 way bearing is NLA. Serial starting with 12+ order Tub seal and 2 SKF 6207 bearings. To replace the bearings. 1. Unplug the washer 2. raise the top 3. remove the front. 4. remove the tub by...

please I have it available. If no one takes. I'm going to attempt to get to it in August with the "If I break it. I break it" Attitude and if I do break it then it's on it's way to the shredder