Search results

A+++ 10% Aren’t all new Miele tumble dryers A+++ -10% with the new bases? As long as it’s a eco speed model that is. They also only have normal compressor unless you have the passion.

I had a W5740 and never liked it, sold my edition 111 W3164 also after purchasing my W1. The W1 range is far better in every aspect in my opinion, especially spin performance, I wouldn’t have another old one

The automatic plus cycle is a slightly less intensive cotton short prog, but it does full length rinses with intensive tumbles (not just distri rinse and drain) along with a 3.5min hold at 1400 after a burst, the burst means it’s 99% gonna be balanced enough to always reach 1400 and not limit. I...

I’ve had my T1 (TEF645 - the most basic A+++ eco speed model with chrome) for over 2yr now and I love it. Times vary a lot depending on what you’re washing but usually it’s between 1-2.5hr for the biggest load of towels you can fit inside (also 650gsm). Bedding usually takes 2hr for me as ours...

Sounds like the air vent for the drain is clogged and/or the hoses connecting it

Stuck laundry I had that happen with my hoover 7kg washer dryer, a full load of towels got dried to the sides of the drum completely. I’ve noticed the new 14kg hoover I used they now do slow tumbles during sensing after the final spin and everything then just falls off, however still not anti...

Yeah heat pumps problems are quite well-known for Bosch made dishwashers, probably the only real common issue they have. I’d say it’s worth it and it wouldn’t put me off buying one again (currently own the Wi-Fi serie 2 range), if it did fail I’d try and replace it myself

My Siemens washer has received like 2 updates since I’ve had it and my Miele W1 has updated around 3 times since I got it in feb. I think the dryer has recieved 1 update and so has my fisher&paykel. Sadly won’t be able to tell you what cotton reaches as I never use the cycle, I don’t dry bedding...

I think the stopping in the auto clean stage is to stop water from being pulled through making clothes wetter again during the programme. Unlike self cleaning where the water runs off the fins immediately it may not in auto clean because it’ll put a thin layer on the filters which will need to...

Reply to #28 Yep quickly went back and this was what I measured with similar loads on Mix plus on the Beko (no low temp option on this dryer), Cotton Normal Gentle Tumble on the Miele and Mixed +2 Low heat on the Bosch. I’ve noticed though that the Beko is quite “stupid” per day since if you...

Bekos duvet prog is kind of similar, if using for sheets and it’s only one set you have to set dryness to less. Mieles bed linen prog I only use extra dry which can dry sheets and duvets with no problem, Bosch? Yeah no reversing so 😂, everyone says how they’ve improved now but only ONE model...

I also find my Bosch has no target temp (it’s the serie 6 self cleaning directselect) and the allergy and towels cycle I believe reach over 70. Including timed dry with “low heat”. I also find my fan glitches sometimes and will constantly cycle on and off no matter what cycle or ambient temp...

Your device will be A+++ on any cycle, the only difference is with hybrid dryers with speed selected but this doesn’t apply to yours. The knocking noise is frequent with Bosch models. I know someone’s who’s had to have a drum replacement, mine also knocked constantly and needed a bearing...

Here’s a few pics of the asko too 🙂

Its saturation is meant to fully soak but less than 9kg cycles don’t do it for long enough and end up going into the wash partly dry. I just done a cycle with a full load of towels on “allergy cottons” which again limited the final spin (respinning as I write this) and it has stored 3 errors on...

Yeah ALOT of programmes are similar and/or not good. E.g Quick is for 9kg but do no interims unless you select super rinse which adds 24min, time prog which goes up to 3hr is only allowing 2kg. Easy care and mix only do a burst as interim spins, cotton doesn’t use prowash but reheats, sportswear...

Yes these fault codes are saved in something like fault code read out or similar, I can’t remember exactly. It always has enough time to heat but if it needs to refill after the water has reached temp the first time, it simply will not heat again. Fisher and Paykel, Miele, Bosch etc do not do...

Yeah it runs completely normal in every programme, it gives no errors until you read out errors in service mode. I don’t think it’s to do with sudslocks as it stored E10 during its 36th cycle which was just a full load of darks on dark wash (no interims on this cycle). I’m not sure if it’s to do...

Hey guys, was wondering if anyone had any knowledge on what may be causing my new asko machine to keep storing a E10 fault relating to a water level sensor issue. It never displays the error in normal user mode and I had no idea this was happening until entering its fault reading menus. It’s...

Bosch/Siemens ‘mini load’ It’ll be interesting to see how efficient the new “mini load” option is on the new Bosch/Siemens TOL lines. For cotton it estimates 31min upto 40c, 40min @50c and 53min above. Wonder if it’ll come close to Mieles SingleWash with PW 2.0. Also looks like the new AEGS...