Search results

I measured the water temp and its 136.8f. Not sure why I thought it was 120. Today I figured I would just clean it real well every where I can and possible replace the seal that I ordered. I went down to look at the machine to see how the soap dispenser looked and what type it is so I could...

I thought 120f was the maximum tap water should be for Risk of burns? That TEAD video was eye opening smell and mold after just 10 loads. Now where to find a powder product with TEAD? perhaps the P&G Arial from Mexico can be found in Hispanic stores and has it.?? The Indian guy on you tube...

Sorry This OP hasn't been back until today. been prepping the house for a hardwood fllor sanding and refinish on both floors. I did just order a seal but can always return it again. and more Affresh tablets. Tennant goes on vacation tomorrow for 4 days. I will plan on washing with bleach and...

I have a real germaphobe tenant who has supposedly had diagnosed brain damage from a house with mold in the past.... the Washer machine was only used for 5 months before she moved in 4 years ago. She is convinced its the door gasket. The gasket looks clean and no smell to me. I did smell a...

since the last video I have observed 2 more loads with hardly any noise, one large and one small . Can it be from room temperature. it possible some loads at 65 and some at 75

Well the sound is back for sure. But at least I know it's an eminent catastrophe. Hopefully I did the utube link correct.

odd it is not sounding unbearably loud on the load just now. it is possible the noise I heard was a unbalanced load in the rinse cycle. Which may be a different issue. I did go look at it and the load didn't look very unbalanced but I also moved the washer around on its sloped platform (with...

well just 2nd load and it appears the sound is coming back. could there be to much wear on the shaft or brake assy splines? Maybe I can find some real thick sticky grease. I inspected the shaft spline real close but maybe it was worn> I didnt inspect inside the brake. The brake assy is like...

i searched wally and no stores here had that grease.

You are right my front cover has a 4" bottom plate. I stopped by an appliance repair place today. He said he has lots of parts but no transmissions. He has new and used on his floor. A similar model LAT96xx was 250$ it had similar controls but no bleach dispenser. I also have a 20...

I haven't posted to YouTube much. But thanks for the help. So I just post my video number after this? https:// w w w.youtube .com/watch?v= I must thanks you guys for inspiration and guidance. Sad to imagine how many hit the trash due to this noise. Seems like an ok design. Except for the...

Well it appears that grease was what she needed. The tranny still moves but no clunking sound. How long the grease will stay in there as it must be being squished back and forth with no seal to keep it in. I bought Lucas marine grease but it wasn't any thicker than my moly lube or and...

the interesting thing about the hair is that there wasn't lots of hair in the cabinet. not lots of hair in our laundry room and never any pets inside the house with this unit. is there a way to learn of the date of manufacture? model LAT9714AAE S/N A0104798KU

I got the brake off. If you would have said to hit the vise grips at their tip near the screw! I was using it like a lever at first. It took more than love taps for sure. Radial bearing feels good. Splines don't look to be worn. I figure they are this multi faceted shape. The...

I did switch the vise grips from what is shown in the picture as this is counterclockwise removal. I have smacked it quite a bit with a dead blow but not like a gorilla.. my vise grips are denting the outer ring of the brake and they pop off after a couple hits. I'm not normally a farmer type...

I did not buy new oil for the transmission. It looks so clean as it was. I did not try running it again as I didn't do anything. do I clamp the jaws of the vise grips on one of those small screw and then push it against the brake assembly as a lever? I called a nearby old appliance store and...

I found some marine grease STP brand at my nearest AutoZone. So I'm starting to go at this Maytag because it's too windy and cold to go fishing. where does all this grease come from That thrust bearing or the acme threads? this is one of the only places I can see to put vice grips on the screw...

so when I take off the brake assy. when I'm goin in with intent to grease up splines what other things should I look for? Do I need to replace any parts like the damper pad kit or the upper bearing while I'm in there? probably will get to this job Tuesday so I have some time to get parts on the...

ok I will put the clean 90 w oil back in. and seal it up. Also painting some shed trim today. its sunny and over 45f

Well The tranny looks nice and tight. no wear that is see... and the pulley turns freely counterclockwise. and smooth as butter in agitation with no rotational movement of the tranny at all. grabbing the yoke I don't feel any play. So I'm guessing this is good news? Before I pull the brake...