1967 Lady Kenmore washer side check valve

[4bagger]

Picked this up a couple years ago and just now attempting to put into service. Along with a few gallons of water on my garage floor, I discovered that the side check valve needs replacing. Part number in the catalog is 86935. Can't locate by that part number anywhere. Found some online, that look the same but none have this part number referenced. If I can track down the part,I assume the tub has to be removerd to replace. Any suggestions would be appreciated.

 

[repairguy]

What a nice washer! I have one in copper tone. That part number crosses over to Whirlpool part number 350397. I hope this information helps and you are able to put this machine back into service.

 

[4bagger]

I was able to remove the half that was attached to the hoses, and found the check valve that appears to be the exactly the same (FSP 89888). I guess I need to remove the tub now to get to the other half. Is there anything I need to know to accomplish this?

 

[4bagger]

I gotten to here, but not sure how to remove agitator. Does the top piece with the K come off?

 

[washdaddy]

the scrubber cap (the part with the letter K) of the agitator screws off. Grab a hold of the trunk of the agitator and than unscrew the scrubber cap. The remainder of the agitator lifts off.

 

[4bagger]

Ok got the scrubber cap off. Should the agitator lift out now? I tried but no luck. Is this stud holding it in?

 

[stricklybojack]

.
It’s just stuck. Try soaking in hot water.

 

[vacerator]

Model number

suggests it's a 1965 model. So does the console style.

 

[4bagger]

Thanks all for the helpful info. I'm at this point now. Does removal require a special tool?

 

[4bagger]

Ok I see a spanner tool does exist. I was able to fit a pipe wrench smoothly without hitting the tub, but ring nut is completely frozen. Soaking in PB blaster. I gotta remember the machine is 55 years old!

 

[stricklybojack]

.
Some of those, depending on brand of machine, come off clockwise I think.
Don’t know for sure, plenty of other people here would though.

 

[bigalsf]

Counterclockwise!

Whirlpool spanner nuts open counterclockwise. Maytag spanner nuts & mounting stems open clockwise (left hand thread).

While using a pipe wrench can work, it is infinitely easier with the spanner wrench. Just a heads up as you proceed sometimes these nuts will loosen only to bind up again on another area of the threads. If that happens the spin tube will turn with the nut. At that point you will have to cut it off; luckily these are in plentiful supply, as well as the spin tube drive block it screws onto.

Good luck & keep us posted!

 

[4bagger]

Thanks. I was wondering if that might be the case. Videos I found show it coming off counter, but I don't think any of the machines were this old. If it is reverse threaded, it's a lot tighter now! Haha

 

[4bagger]

Yeah I figured that a tool is necessary, so I bought one on ebay. I'm assuming even after the nut is off, the tub isn't gonna want to just slide right out. Found a good video showing how to remove a stuck tub with the spanner tool and slide clamps.

 

[yogitunes]

take the nut off...stand inside the machine, pretend your on a see-saw, and shift your weight from one leg to the other with force...one or two tries should break it free....then lift out....

 

[4bagger]

Spanner tool arrived today and got the lock nut off. Tried see-sawing basket out, but no luck. Also sprayed generous amounts of penetrating oil and tapped the sleeve of the basket with a rubber mallet. Any other tricks I can try?

 

[DADoES]

 
Keep trying the same procedures until it comes loose.  Took me a week to get the basket loose from a WP/KitchenAid direct-drive that had not been disassembled in 24 years.

 

[combo52]

Removing Stuck Basket On A BD WP Washer

Did you try standing in it and moving your weight from SXS ?

I have never had this not loosen one in less than 60 seconds and I am only 150 pounds

John L.

 

[4bagger]

Ya I actually did try standing on machine and pulling up side to side. I weigh about 180 lb. Gonna give it a few days of soaking in oil and try again.