Sunbeam CoffeeMaster C-30A

Automatic Washer - The world's coolest Washing Machines, Dryers and Dishwashers

Help Support AutomaticWasher.org:

stan

Well-known member
Platinum Member
Joined
Oct 20, 2010
Messages
2,083
Location
Napa CA
I've had this for years and it's used occasionally.
Of course the rubber gasket has gotten so hard that it's difficult to separate the bottom from the top. But impossible now to put the two together without hot water ect.
I've looked online for gaskets, and found Dayseal.com.
Has anyone replaced their gasket, or used this Co?
The glass tube in pic 2 is the only filter it's ever had, or that I've used?

stan-2015052423423208324_1.jpg

stan-2015052423423208324_2.jpg
 
I purchased a new gasket from Dayseal for my Cory glass vac pot. While it was more pliable than the old gasket it was too slick to make a good seal once the pot heated up. Therefore, the upper bowl wouldn't stay in place after the water had risen to the top unless I held it down. This made it difficult to make a pot of coffee. I haven't had any experience with the replacement gaskets that they sell for the Coffeemaster, maybe they work better than the Cory. As for the filter rod you have, its a Silex, and they work OK, but I like the Cory glass rod better myself. They are readily available on Ebay. I have also used the Yama filter in my Coffeemaster and they are great, you can buy these online at Sweet Maria's.
 
I've Bought The Coffeemaster Seals from Dayseal

The first one lasted about a year. Good fit, but a little softer than the original.
What happened about a year later was it started to deform. Eventually it wouldn't hold the seal. Dayseal said that my Coffeemaster was too hot and sent me instructions about how to turn the heat down on it during brewing. I just moved on to a Cory Glass pot and never fooled with the Coffeemaster again. The Cory pot is much easier to clean and can be thrown in the dishwasher.
 
A real Coffeemaster filter makes much clearer coffee than the glass filter. If you go doing anything about replacing the filter, remember that there is a stainless steel spring in it with fins that fit down into channels in between the inner and outer folds of rubber so don't throw that away. One day you might find a good gasket and you would need the spring to make it work.
 
Tom

This is the only filter I've ever had, so I'm not sure what you mean?
Do you have a pic?
If I put hot water in the existing gasket, I can put it together. After brewing while hot, it come apart easy enough.
Ordered a new gasket from Dayseal, We'l see!
 
Try ebay for Coffeemaster filters. I've purchased all of the the ones I've ever used on ebay. If you get the filter frame for the cloth filter you can use a small french press filter in place of the filter clothes, which are difficult at best to find. If you desire a clearer brew than the french press filter alone provides, place a 3" paper coffee filter on top of the french press mesh. I personally prefer using the mesh without the paper as I don't care for the flavor imparted by paper. It is true as Tom said, you get a clearer brew with the cloth filter, but you can't beat the ease of cleanup when you use a Cory glass rod, the New Cory filter rod is the best, also check out ebay for these. They filter much better than the Silex glass rod, I've used both and the Cory is better. In fact, in my experience I've noticed less sediment in the finshed brew using the Cory rod as opposed to the mesh filter alone. It's fun to experiment using all the options until you find the one you like best. Also, keep in mind that if you do use the cloth filter you have to clean it after each use, and don't use soap or detergent, it will adversely effect the flavor of your coffee. When I used the cloth filter for a while, I would rinse it out throughly, then place it in a small jar of water in the refrigerator. Once a week boil it in water with baking soda, the rinse well. It's a hassle! Hence the glass rod, LOL. BTW, if you can get the top bowl off when the pot is hot, I'd just contiue to use it this way, after all you have to take the top bowl off before you can pour the coffee anyway, and presumably you would be doing this while the pot is hot, so save the $, and spend them on getting a filter set up that you like.
 
Thanks

Eddie and Tom for the info and advice with this.
I've thought the same thing Eddie about leaving well enough alone. What I've been doing is..
After use, I clean, and get the gasket hot enough for me to get it together with the glass rod I have in place. And it's stored that way. When I'm ready to use, it's too hard to get apart, so I measure out the amount of water and pour it down the top, making sure it runs down to the bottom, then I put the grounds in the top, plug in and go.
Of course when it hot it comes apart. Its when it cold that I fight to pull apart, or worse to get together.
 
You may also want to do a Ebay search on Sunbeam Coffee Filters too. I have found some of the cloth ones available without the mention of Coffeemaster in the auction. They were the correct filters.

Both of my C-30 Coffeemasters came with cloth filter frames. I do have a metal mesh filter for a Sunbeam Coffeemaster C-50 though.
 
Hi Guys

got the new gasket and am having a hell of a time getting the old one off!
I should have ordered the smaller inner seal as well, guess that's may be next. It's so hard that I'm trying to boil it to soften and work off a little at a time.
Any other suggestions?
Thanks

stan-2015053100262203043_1.jpg

stan-2015053100262203043_2.jpg
 
To remove mine I just grabbed the edges of the rubber seal with my fingers and then with my thumbs pushed outward on the metal center while pulling back with my fingers and the metal part just popped right out.
 
Couldn't get

Anything to pop out LOL
This thing was so dry and hard!
Had to keep it hot in order to get any pliability. Took a while, but got it out. But looks like I've got to order the smaller rubber piece too.
Then remember how it all went together !

stan-2015053101522501483_1.jpg

stan-2015053101522501483_2.jpg
 
Hi Tom

The smaller piece is in pic 2
Its actually called a secondary seal.
When I ordered the larger one, it was recommended that the secondary one be replaced too.
I can see why now, there was no way I could have gotton the main gasket of with out destroying the secondary. They both felt like Bakelite
 
Originally, that was all one piece with pockets for the spring between the inner outer rings and a pocket for the small metal plate in the middle in the inner part of the ring. I used to replace them on mine when I could still get the originals from Sunbeam.
 
Thanks Tom

That explains part of the problem I had getting the old one off.
As it was coming loose, it looked the way you described.
Here a pic of the new gasket. I thought the secondary gasket was Bakelite until it started coming apart!

stan-2015053115331808047_1.jpg

stan-2015053115331808047_2.jpg
 
Seal intallation?

How did you reassemble? when I got my seal, it does not fit the base well and has too much room for the threads to engage. Also, I see on another thread that you left out the spring (thing with the teeth).
 
Fix for Sunbeam C30 gasket

Hi, new member here.
Re: Sunbeam c30 gasket
I thought to myself that perhaps the (very) hard gasket could be sanded down a little so it would fit. I had nothing to lose because I was planning on ordering a replacement at dayseal.net. Anyway, it can be done because I just did it. You can fix this problem for the cost of a sheet of sandpaper. I removed the gasket by unscrewing the inverted spout under the upper pot that acts as a retainer for the gasket. I dry sanded (though I now recommend wet sanding because the black dust it produces gets messy) it by grasping the gasket with the sandpaper and repeatedly twisting the gasket to slowly reduce the part of the gasket that comes in contact with the lower pot. It took a while of sanding, slowly removing material and incrementally reducing the diameter. I checked the fit on the lower pot frequently. I stopped when I could get the gasket to fit, but very snugly. You want to stop when it fits, but very tightly because it does still need to enable a vacuum to draw the coffee down. The taper of the gasket aids with this sealing so your sanding does not need to be super precise. Just sand it enough so it will go on. Got it? Very easy! Super cheap! Does require a little "elbow grease", okay?
 
Back
Top