Kenmore Eighty Series set

Automatic Washer - The world's coolest Washing Machines, Dryers and Dishwashers

Help Support :

captainmoody

Well-known member
Joined
May 22, 2006
Messages
348
I found a Kenmore washer/dryer set this morning while dropping off a load of scrap at the recycler. They charged me 12.50 each for the both of them! Aside from the top left side enamel being chipped on both units, they are suprisingly clean and complete.
My question is how old are they? I am guessing 1960?
The model and serial numbers are:
Washer:
110 5905803 Stock 9580
Ser C521052
Dryer:
110 5907802 Stock 9780
Ser M527819
I am pretty happy about this find as they are a pair and I won't have to go hunting down one or the other!
Is there anything I should check/replace before powering them up?

6-15-2006-15-00-30--captainmoody.jpg
 
Wonderful find, one of my favorite sets. By the way, your washer is missing the transmission braces that secure it to the frame. Probably the belt was changed at some point and the previous owner didnt bother to put them back on. They are rather important ot keep your tranny and spin tube aligned in the bearing shaft. You can probably find three more off another old washer at some point. The FSP service manual always tells the owner to be sure and
reinstall them.
 
Nice 1959 Kenmore set!

Those are from 1959. Hi Jimmy, the transmition braces were not added until 1961 on KM/WP.
 
I can hardly believe...

that these were taken to the recycler. What a shame if these had been crushed. I am so glad you got them. What a great find and add to your collection. Gregm has the same machines in his collection I think. Best of luck. Patrick
 
Hi Rick, I never new that! Thanks. I had a 1960 set that never seemed right, It had them on it, but they never looked correct. The tranny in mine had been changed once before, so maybe someone added them at that time....I replaced the bearings in it once but they wore out again after using it for many years. I finally scrapped it because of that.......the bearings never did seem to fit the spin tube correctly........
 
KM/WP transmition braces

I wonder if the braces were added as the capacity was increased Jimmy? A more powerful motor,and the increased fill height were the the only other changes that I know of.

BTW: I swapped out the pressure switch in the 56 WP for a higher fill,and will do the same thing for the 56 KM I am working on now. The originals cannot be adjusted high enough. I have to have the tub FULL on my machines! No water shortage around here.... LOL!!

6-15-2006-17-18-55--rickr.jpg
 
Wow! Nice machines greg! I will need to do a lot of cosmetics to get mine like that.
I have another question, this time about the dryer. I noticed it has a lint bag? How is that supposed to work? Is it like a vac bag? the one in my dryer is all taped up and looks pretty sad...
 
captimmoody,

good save. Were they ready to go in the grinder/krusher?

It makes me wonder how many on a daily basis that we don't even know about. SCARY for us.

Steve
 
Nice score Dwight! I spotted the same dryer at a local Menard's a few months ago - if it had the matching washer, I would have sprung the large sum of 18 dollars for the set. This is one of my favorite Kenmore designs - you'll love'em!

Ben
 
Fantastic!!! I am so horrified that they were almost crushed. It's like wheeling your old granny to the cemetery and leaving her there in her wheelchair, or something.
 
Dryers need love too...

Fantastic save! Could you please tell me more about the dryer; gas or electric. And perhaps some close-ups of its controls, panel, inside, etc.

Thanks and congrats.
 

Latest posts

Back
Top