Hi all I know that some have asked the question at how high the Extra Large water level on this washer...so here it is. Washer.
Speed Queen washer AWN311 water level
- Thread starter nmassman44
- Start date
Help Support :
cascade waterfall fill
ex large water fill height...no adjustments at all.
rll70sman
Well-known member
What would you recommend?
Mike, would this machine be a good replacement for a Kenmore 500 series washer? Have you purchased the dryer yet or know of anyone who has it and has reported on its performace?
Mike, would this machine be a good replacement for a Kenmore 500 series washer? Have you purchased the dryer yet or know of anyone who has it and has reported on its performace?
You can clearly see that if I do a load that fills the washbasket to the top row of holes this water level wont work in previous pic...this one will though...after I adjust up
Wash action...love the 210 arc and at 68 strokes per min its very powerful yet gentle
another shot
Swirl away spin draining
That unadjusted level looks low. Maybe it was an intentional change by SQ, but on our AWS (the series made just before the AWN) the extra large water level comes just to the top row of tub holes. A call or email to Alliance can help answer that.
Also, I'd love if someone could figure out exactly how these washers read water levels, and if this metering system can be adjusted. It's not a simple timed function, because if you decrease water pressure, the washer takes however much time it needs to reach whatever level was selected.
Also, I'd love if someone could figure out exactly how these washers read water levels, and if this metering system can be adjusted. It's not a simple timed function, because if you decrease water pressure, the washer takes however much time it needs to reach whatever level was selected.
Rll this washer would be a great replacement for a Kenmore washer. This washer is tough as nails and very well made. The dryer friends of ours have and they love it. Its very fast and even though its a thermostatic control dryer not electronic control..ie moisture sensors in the drum...the thermostats are very accurate and what amazes me at how well it does. Once the they cycle the timer moves and an average load takes no more than 35 mins to dry. The washer spins faster than your Kenmore at 710 rpms. This washer also has a good lint filter as well. Self cleaning of course. The washer is also rock steady during spin with no vibrations and the spin is smooth like a Maytag. The washer doesnt index the washbasket like when we got it. And so far the break in period has gone well. The washer is very Maytag-esque...the way they used to be.
Wash performance is top notch and on par with that MaytagSamsung Neptune that we got rid of. Cycle times are fast. 35 min for a load and rinsing is very good as well. Do I think we made a good purchase?...Hell yeah!
Wash performance is top notch and on par with that MaytagSamsung Neptune that we got rid of. Cycle times are fast. 35 min for a load and rinsing is very good as well. Do I think we made a good purchase?...Hell yeah!
The water level is a normal pressure fill system. Not timed. Until the water level pressure switch is satisfied the washer will not agitate. I read the repair manual for the washer and it said that if a customer isnt happy with the preset water levels that the screw at the water level can be adjusted no more than a half turn since each quarter turn equals an inch of water height. I am tempted to do the adjustment myself. The water level height that comes from the factory means that the washer uses just 31 gallons per load. Plus one big plus is that the water temps are not "dumbed down". Warm is a nice warm 100 degrees and cold is well tap cold. Hot is whatever is coming out the tap. Mine is set at 140 degrees. So I have a nice hot wash. All rinses are cold.
rll70sman
Well-known member
Can this washer be "tricked" to run with the lid open or does it have a lid safety switch hidden below the control panel? Also, does it "dumb" down a hot or warm water wash? I hate the fact that Whirlpool incorporated these features in the Kenmore model I have.
1. Yes, easily. We used a long bungee cord, put one end under the washer in back (on the right side, looking at the front of the machine), and the other end hooks onto a metal lever that is visible underneath the top control panel in back (this is the lever that extends to the lid switch). A 30" cord is a perfect length -- don't put too much pressure on the metal lever as it can be damaged.
2. No automatic temp adjustments on these top loaders. None. What you feed it is what you get for both hot and cold.
2. No automatic temp adjustments on these top loaders. None. What you feed it is what you get for both hot and cold.
mysteryclock
Well-known member
JeffG -- I think the slightly low default water level is a way to get away with a water factor below the max allowable in the next wave of Energy Star standards: <= 9.5 by 2011 for top-loaders. 31.4 gallons / 3.3 cubic feet max capacity is, shockingly 9.51515... which is pretty darn close to 9.5 isn't it?
Amazing how those things work out?
Amazing how those things work out?
John, if it's just a matter of a screw adjustment, I have no problem with Energy Star standards. 
Even though the difference in water levels is only a couple of inches, the difference in performance is more than slight for large loads. Those "extra" few inches of water are important.
Even though the difference in water levels is only a couple of inches, the difference in performance is more than slight for large loads. Those "extra" few inches of water are important.
rll70sman
Well-known member
Oops, sorry, Mike, I didn't see your reply about the automatic temperature control. I may just have to switch out the Kenmore washer and Whirpool dryer for a pair of Speed Queens that have features people actually want (and made in the United States). Then, I'll send a copy of the sales receipt to Sears and Whirlpool to let them know I'm no longer satisfied with their laundry products.
Also, you mentioned that the water level can be raised by turning an adjustment screw. I'm curious about that. Could it be done easily without having to take the control panel apart?
Also, you mentioned that the water level can be raised by turning an adjustment screw. I'm curious about that. Could it be done easily without having to take the control panel apart?
The adjustment can be done by taking off the access panel to the control panel in the back. Find the water level switch and turn the set screw I wanna say clockwise only a quarter to half turn and no more. The manual is online I will have to post the linkie.
