boboh1
Well-known member
Is it OK to transport a vintage Maytag washer lying down on the backside or does it have to be transported in the upright position?
Transportation Of Maytag Washer
- Thread starter boboh1
- Start date
Help Support :
Back side isn't the best just because of the drain hose and water valve protrusions. I prefer to move the on their side. It does't really matter which side but I generally try to put the left side down just because the motor is on that side and it lowers the center of gravity just a bit.
because of the drain hose and water valve protrusions.
Personally, I prefer transporting them on the back. The top cover has a rear overhang which offers some protection to the inlet valve and on later models the inlets are recessed anyway.
The drain hose is pain, I prefer to remove it for transport whenever possible. Also, laying on the rear hopefully limits any damage to back panel where it won't be seen once installed.
Just my 2 cents...
Personally, I prefer transporting them on the back. The top cover has a rear overhang which offers some protection to the inlet valve and on later models the inlets are recessed anyway.
The drain hose is pain, I prefer to remove it for transport whenever possible. Also, laying on the rear hopefully limits any damage to back panel where it won't be seen once installed.
Just my 2 cents...
not that it has any real effect on some machines.....but it may help sometimes to open the unit and secure/center the tub and suspension for transport....
these noodles are inexpensive, quick, and easy to install!....just a thought
www.automaticwasher.org
these noodles are inexpensive, quick, and easy to install!....just a thought
GE FilterFlo transporting help
Many members have had a few problems when transporting GE FilterFlo's on their back or sides, main reason is that tub to trany seal popping off..... and I have to transport one, on it's back, for delivery and I don't want this to possibly happen.....so I came up with this..... went to Dollar...
www.automaticwasher.org
Whichever way you move it, be careful to secure the lid by taping it shut. I've heard horror stories about console damage to 'Tags when moving them!
(Bumping an old thread, as it seems like the best place for related questions. 
)
For the center-dial Maytags, is there anything wrong with transporting a washer laying down on its FRONT? Obviously you would have to be extra careful during the loading, and it would have to be laying on something both flat and soft... But are there any structural or other reasons why it shouldn't be done?
Second question: Aside from opening up the panels to insert padding to stabilize the tub, are there any other "gotchas" for sideways transport? (Example: does the bleach dispenser get knocked around? Or are there any differences for suds-saver models?)
Thanks
)For the center-dial Maytags, is there anything wrong with transporting a washer laying down on its FRONT? Obviously you would have to be extra careful during the loading, and it would have to be laying on something both flat and soft... But are there any structural or other reasons why it shouldn't be done?
Second question: Aside from opening up the panels to insert padding to stabilize the tub, are there any other "gotchas" for sideways transport? (Example: does the bleach dispenser get knocked around? Or are there any differences for suds-saver models?)
Thanks
bendixmark
Well-known member
Shipping
The machine should not be on its front as the tub support bracket will dig into the front panel.It should be on its side only.Maytag made a shipping ring that went in the tub opening and it is preferable to have that in place to prevent damage.
The machine should not be on its front as the tub support bracket will dig into the front panel.It should be on its side only.Maytag made a shipping ring that went in the tub opening and it is preferable to have that in place to prevent damage.
Mark, do you happen to have a picture of what the factory shipping ring looked like?
Thanks.
Thanks.
this thought did hit me......and these have worked out so far on a number of machines......they can be altered to fit a number of different situations....
www.automaticwasher.org
GE FilterFlo transporting help
Many members have had a few problems when transporting GE FilterFlo's on their back or sides, main reason is that tub to trany seal popping off..... and I have to transport one, on it's back, for delivery and I don't want this to possibly happen.....so I came up with this..... went to Dollar...
www.automaticwasher.org
I've used duct tape, to hold the tub assembly in place, during transportation.
Moving A Maytag Washer
Is best with the washer on its side or back, if you don't have the shipping ring take the front panel off and pack heavy foam or padding around the top areas of the tub to keep it from moving around too much and denting the outer cabinet.
Do Not put anything inside the tub as this will not help at all and can actually increase the chance of damage by making the suspended tub assembly heaver.
John L.
Is best with the washer on its side or back, if you don't have the shipping ring take the front panel off and pack heavy foam or padding around the top areas of the tub to keep it from moving around too much and denting the outer cabinet.
Do Not put anything inside the tub as this will not help at all and can actually increase the chance of damage by making the suspended tub assembly heaver.
John L.
bendixmark
Well-known member
shipping ring
I don't have a picture but it was a white plastic maybe 3 inches tall.There must be some around.I have a few but I am hoarding them,(among other things)use them all the time.At one time time I had an arsenal I used to save them from every delivery.
I don't have a picture but it was a white plastic maybe 3 inches tall.There must be some around.I have a few but I am hoarding them,(among other things)use them all the time.At one time time I had an arsenal I used to save them from every delivery.
Thanks Mark. If you ever do pull one out in the future, and have a chance to take a picture, keep us posted!
Hang on, is this it?
(Originally psted by redcarpetdrew in this thread:
Going thru the 1972 Maytag A806/DE806 set
www.automaticwasher.org
(Originally psted by redcarpetdrew in this thread:
Going thru the 1972 Maytag A806/DE806 set
Going thru the 1972 Maytag A806/DE806 set
I posted some pics of the Maytag set I had just picked up a little while ago. The little old lady who owned them for 37 years was worried that they'd go to the junk. She wanted someone to take them, fix them and give them a home for a long time to come. Seeing how she cared for them, I'm not...
www.automaticwasher.org
mayken4now
Well-known member
Yuppie, just used mine today to change the pump when tilted back. 38 years of service, went bad this week, only with a loud squeal.
I've also seen Styrofoam equivalents of the shipping ring.
harpon
Well-known member
How about a bucket turned upside down and maybe some noodles or padding around that to keep the tub centered?
Just a thought.
Just a thought.
