Vintage Hobart Buffalo Chopper

Automatic Washer - The world's coolest Washing Machines, Dryers and Dishwashers

Help Support :

Those Hobart choppers are popular out my way at the Carolina BBQ places.The Hobart machines show up in the used restuarant equipment places from time to time.they can also be used with other Hobart attachments-meat grinders and such.the Capitol BBQ place here in Ayden has a HUGE floor mounted Hobart chopper.They need it-the most popular Carolina BBQ place in the area!So Good!
 
Hobart Buffalo

That is a Very Old Model.  When you want to change out the bowl, you take off the cover, and at the base of the motor, there is a large Thumb Screw. Loosten that and the Whole Motor tips to the left.

 

Very Powerful and Dangerous Machines.  I use one everyday at the restaurant I work at and it is pretty rare that I'll let anyone operate it until I've instructed them how to use it, and then I'll stand there and watch them at least a dozen times or so until I am comfortable with their use of this machine.  Those spinning blades could easily take off multiple fingers or a hand.

 

That Model is also Direct Drive which the Newer Version that I use (1974) has a belt drive system.  I don't think they make those anymore.  Stevet ???????
 
Buffalo Chopper Vs finger!

My Grandmother cut her little finger off with one of these in the late 50s, She worked in a school lunchroom and was making slaw and pushed the cabbage TOO far, when she pulled her hand out her little finger was hanging by a piece of skin!!, Our local surgeon sewed it back on, she didnt lose it, but it was stiff from then on,so yes, these things can take off fingers quickly.
 
Interlock

Yes there is one, but the design of the machine is Very Scary as the opening where the food goes in and comes out is wide open and one could definately (through not paying attention or being careless) loose fingers or even a hand.
 
So,while using the Hobart Chopper---KEEP HANDS AWAY!!!Would have thought the opening for the blade guards would be not large enough to allow a finger or hand to get under it.Haven't examined one of these tools in awhile.so,treat it with the same respect as a power tool like a table,radial,saw,or a band saw-WATCH WHERE YOUR HANDS ARE!!!And another tool where you should watch where your paws are---Sheet metal squaring shears-manually powered(foot treadle) or powered.Any of the above tools will give you a quick and undesired manacure!
 
At our plants we have several of the big choppers that are 8 to 12 feet across to blend ingredients to be added to chopped and formed chicken nuggets, patties.  Our covers cover it all while blending the raise and the blades stop but the bowl turns to empty against a shield into a converor belt or a large cart that then goes to the large miser to blend with the meat and be chilled so it can be formed then go through a predust, batter, breader cycle and into a fryer to be either fully cooked or par fried (to set the coating) then into a big spiral freezer and on to packaging.

 

 
 
Dangerous Tools!!

Anyone who ever worked in a furniture plant knows what a veneer clipper is!! A huge air operated knife!! it will clip off a hand just as quick as it will a two inch thick stack of veneer panels!!
 
#2

This is the machine not yet assembled for Chopping. This is the way the Dishwashers must put the machine away after they wash the parts.

I want no one to assemble this machine unless I have instructed them to and have been authorized by me

toploader55++2-27-2012-11-02-57.jpg
 
#4

Here is the Machine with the Cover in Place. There is a Knob on the back of the cover which only when everything is aligned and assembled properly will engage the safety switch to let the operator turn it on.

The Bowl rotates from Left to right. Notice the Large openings at both ends of the Cover which can Very Easily accomodate a Whole entire Hand.

Under the Dome in the Center of the Cover is where the Blades are spinning at 3450 RPM.

Safe Machine ??? I THINK NOT !!![this post was last edited: 2/27/2012-11:29]

toploader55++2-27-2012-11-09-25.jpg
 
#5

Here is a Pic which I took by angleing the Camera to get a shot from the bottom of the Bowl as to what it looks like under the cover.

Note the Precise Clearence Proximity of the Tip of the Blade to the bowl.

The Product to be chopped should be cut down into a Uniform Cube or Dice to insure uniformity of processing. Another words , you should Quarter the Onions, Or rough chop the Celery, Carrots, or Meat so when it goes through the machine it comes out evenly and uniformaly chopped. The more revolutions the bowl and product go though, the finer the product will be.

I should have shot a video of it running. Maybe I'll go back later and do that.

This is Hobart Quality Engineering. It's no wonder why there machines last this long.

toploader55++2-27-2012-11-13-52.jpg
 
#6

This is the "Power Hub.

The Lever on the Left Engages and Disengages the PTO. (Power Take Off) from the Drive Motor.

This Hub powers accesories such as a Meat Grinder, Power Shredder/Slicer, Power Dicer etc.

This machine saves Hours of Slicing, Shredding and Chopping per day.

Only good for bulk items, I still use a Cuisinart type processor for smaller batches of things such as Chopping Shallots, Garlic and Pureeing smaller quantities.

toploader55++2-27-2012-11-25-0.jpg
 

Latest posts

Back
Top