GE Top-loader in the house

[toggleswitch]

Can't have too many holes in plastic!

If there is not a hole where it needs to be, the water will travel UP till it finds one hence the staggered pattern of the holes.

Remember there were machines with non-perforated tubs. IMHO not a factor as to spin-dry effectiveness.

 

[toggleswitch]

Let me have a peek....

I'm gonna pry that front panel off and get a pic for y'all!
STAY TUNED!

Same bet time, same bat station!

http://www.repairclinic.com/0100_24.asp

 

[toggleswitch]

Steve:

GE® 3.2 Cu. Ft. Super Capacity WasherModel#: WDSR2080DWW

 

[toggleswitch]

Steve:

GE® Extra-Large 6.0 Cu. Ft. Capacity Gas Dryer
Model#: DWXR483GBWW

I think this is my dryer.
Mine has a SS Drum.

(doing this from my job.)

http://products.geappliances.com/ApplProducts/Dispatcher?REQUEST=SPECPAGE&SKU=DWXR483GBWW&SITEID=GEA

 

[foraloysius]

It looks like the stainless steel drum is only available on the 7.0 Cu. Ft models.

Is yours perhaps the DRSR483GDWW?

http://products.geappliances.com/ApplProducts/Dispatcher?REQUEST=SPECPAGE&SKU=DRSR483GDWW&SITEID=GEA

 

[toggleswitch]

YAH, Thank You.

Welcome to America, where bigger is better.

 

[toggleswitch]

Hose Extension

Went to Homo Depot and got me a hose extension!
and some magic magnet to bypass the lid switch

The washer drain hose does need to go into the stand-pipe thereby bypassing the slop-sink and the required pump for that sink.

Of course, it is easier than it sounds

 

[toggleswitch]

It leasks, natch!
Surgery of that magnitude usually has some complications.

Methinks i need to clamp each piece of rubber/plastic to a piece of metal pipe rather than to each-other.

 

[toggleswitch]

Tested it with a *SMALL* Water level, as seen in pic.
Leaks like a sieve - *SIGH*

*LARGE* setting (actually a medium fill) goes to third row of holes from top.

*SUPER* setting goes to top row of holes.

 

[toggleswitch]

Magnets to bypass lid switch.

Believe it or not this was taken while spinning!

Smart little manufacturers, you need TWO magnets to do the trick (or i'm an idiot!)

 

[toggleswitch]

OK I think I have posted WAY too much.

First time the washer is cheesy and the dryer is nice for me!

TA TA for now!

 

[westytoploader]

Wait....

How about some action shots of the next load?? ;-)

 

[toggleswitch]

I'll try.

But the camera freezes the spin.
How can I get videos I make posted?

 

[agiflow]

Yeah guy...what about those action shots!

 

[toggleswitch]

well let's see if I can clear a day (to have a wash-in) with her highness Madame X.

If so come on down~~~~~ NY, NJ, CT, PA, MA, etc!
*We'll have the classic GE Filter-flo
*The new GE plastique mess,
*The Frid-Ge-More, it it has not flown the coupe to go to Yiayia Bubble's (grandma's) house.
* The EASY table-top washer is also still here....

 

[westytoploader]

Let's see...first it was Madame Kurva...then Queen Cloaca, now Madame X.

I have a new name suggestion--since one of your favorite sayings is "Who luvs ya baby?", instead of Kojak, you could be Bojack!

LOL...be sure to include pics so us Southerners can participate vicariously! ;-)

 

[mickeyd]

looks over shoulder; begs for shower

Toggledeedee and Toggledeedoo
Easy Spin has a present for you

An aqua, Jet-Swirl GE fabric softener dispenser
Nice and clean, but from an old model that fits over a wide agi cap

When settled and ready for accessories, I'll send it to you.

Someone else wanted a mini-basket--have it
Again, old, for a three-vane wide-capped agi, plus matching filter-flo
Let me know

 

[SactoTeddyBear]

Re: Magnet to Bi-Pass Switch:

What if you use only 1-Magnet and place it in the opposite direction, centered on the Magnetic Rubber Cover, would that allow you to only need 1-Magnet to have the Washer operate with the Lid Opened?

Fun Times with a GE Wash-A-Matic {LOL}, Steve
SactoTeddyBear...

 

[SactoTeddyBear]

Re: Magnet to Bi-Pass Switch:

What if you use only 1-Magnet and place it in the opposite direction, centered on the Magnetic Rubber Cover, would that allow you to only need 1-Magnet to have the Washer operate with the Lid Opened?

Fun Times with a GE Wash-A-Matic {LOL}, Steve
SactoTeddyBear...

 

[SactoTeddyBear]

Re: Sorry Robert:

I was having problems with my Thread to send for Posting.

Gracious Apology, Steve
SactoTeddyBear...