Different automatic washer, suspension systems
Hi whirlpool 862, GE filter flow washers from 1961 through 1995 had a hanging suspension system. They had no springs in the suspension system, the entire inner wash basket agitator transmission motor assembly was hanging on a cable from the top of the cabinet. It was a crude suspension system much like whirlpool belt drive machines that hung from the top of the cabinet, the thing that made the whirlpools work better was the fact that cabinet was 29 inches wide and had good self leveling feet.
GE filter flows walked like crazy until they put self leveling feet in the back in the mid 60s. They were a lot better after that, but it was still a crude machine that couldn’t take a lot of speed.
GE filter flow machines again were very crude the very first load you did in the machine if it went out of balance, the inner tub was striking the outer tub and the porcelain enamel was flying everywhere in time. A lot of them rusted through because the enamel was worn away where the two tubs contacted each other.
Currently on top loading washers, the most sophisticated suspension that allows the fastest spin speeds without excess noise and vibration are hanging suspension machines.
I have never seen a T model GE washer damage itself from an unbalanced load. This is just plain nonsense. The original T model machines had little rubber straps in the four corners at the top designed a suspension limiters it was found that with better hanging spring struts that these were not necessary so they were eliminated if they break as they often did on the early models. It didn’t make any difference.
And just to reiterate, every front load, washer is hanging suspension machine hanging suspension machines have the advantage of a much more rigid solid cabinet because the cabinets not just there to hid the mechanism. It’s actually a structural part of the machine.
As to oiling the pump bearings on Maytag dependable care, water pumps it certainly not a bad idea after 20+ years, but keep in mind. I have never seen a Maytag washer pump seize from lack of oil. The only time they failed is when water gets past the seal into the bearings and also rare cases where the impeller comes loose on the shaft or the fins actually wear off the rubber impeller and then they don’t pump water anymore.
The removable screw is not really meant as an oiling point. The screw is there to hold the diecast bearing holder in place in the plastic housing, if Maytag had wanted the pump to be oiled, they would’ve put a more convenient size oiling port on the pump.
John L
Hi whirlpool 862, GE filter flow washers from 1961 through 1995 had a hanging suspension system. They had no springs in the suspension system, the entire inner wash basket agitator transmission motor assembly was hanging on a cable from the top of the cabinet. It was a crude suspension system much like whirlpool belt drive machines that hung from the top of the cabinet, the thing that made the whirlpools work better was the fact that cabinet was 29 inches wide and had good self leveling feet.
GE filter flows walked like crazy until they put self leveling feet in the back in the mid 60s. They were a lot better after that, but it was still a crude machine that couldn’t take a lot of speed.
GE filter flow machines again were very crude the very first load you did in the machine if it went out of balance, the inner tub was striking the outer tub and the porcelain enamel was flying everywhere in time. A lot of them rusted through because the enamel was worn away where the two tubs contacted each other.
Currently on top loading washers, the most sophisticated suspension that allows the fastest spin speeds without excess noise and vibration are hanging suspension machines.
I have never seen a T model GE washer damage itself from an unbalanced load. This is just plain nonsense. The original T model machines had little rubber straps in the four corners at the top designed a suspension limiters it was found that with better hanging spring struts that these were not necessary so they were eliminated if they break as they often did on the early models. It didn’t make any difference.
And just to reiterate, every front load, washer is hanging suspension machine hanging suspension machines have the advantage of a much more rigid solid cabinet because the cabinets not just there to hid the mechanism. It’s actually a structural part of the machine.
As to oiling the pump bearings on Maytag dependable care, water pumps it certainly not a bad idea after 20+ years, but keep in mind. I have never seen a Maytag washer pump seize from lack of oil. The only time they failed is when water gets past the seal into the bearings and also rare cases where the impeller comes loose on the shaft or the fins actually wear off the rubber impeller and then they don’t pump water anymore.
The removable screw is not really meant as an oiling point. The screw is there to hold the diecast bearing holder in place in the plastic housing, if Maytag had wanted the pump to be oiled, they would’ve put a more convenient size oiling port on the pump.
John L
Last edited:
