HOOVER A3786 LOGIC WASHER

[optima]

Logic

Henry,

I still have the Ultima WM72N but the circuit boards have been repaired about 3 times now without any success so i'm waiting for a old Ultima to turn up so i can transfer the boards into mine.

CJ,

I have watched all your recordings on Youtube & i really enjoy watching them. Well my Logic has the turquoise paddles so i guess it has had a drum replacement in the past. I have downloaded a instruction book from the Hoover website but it's for a Logic 1000 spin, but apart from that it's exactly the same.

 

[optima]

Logic

Well the new thermostat landed today.

 

[optima]

Logic

Thought it would be just a matter of pulling off the old stat & pushing the new one on without having to remove the rubber seal but there was just know way of pushing it on.

 

[optima]

Logic

Seal removed.

 

[optima]

Logic

Just to be make sure that it would be water tight i applied a generous amount of sealant all the way around the seal & around the thermostat housing before really struggling to push it back on. So what i thought would maybe take 5 minutes to do ended up taking well over 30 minutes. I will let the sealant dry over night & i will try it out tomorrow. Fingers crossed it will now heat up to the correct temperature!

 

[hotpoint95622]

hotpoint 95622

Seal, yes the rubber grommets can be a little tricky at times, I have found it’s best to remove them, give it a good clean and then re-seat the complete unit. Some times a little smear of washing-up liquid can help if very troublesome.

Back of the drum is nice and clean, no signs of being in a hard water district.

Lee

 

[jmurray01]

Looks like it is in great condition!

I bet it doesn't take hours to complete a load eh ? (Just a little dig at my Beko WM5100W by the way).

 

[henrypeter21]

Fan of the WM64!

Excellent Progress, Keep the updates coming.

When i did the thermostat on my Zanussi, i found that it was not the stat causing the heater not to work, it was the plug terminals on the heater. The ends have worn down so I scraped the end where the plug had been against the wall, then refitted and it worked fine.

I am currently doing an electrical project including writing my own programs after seeing lees project that he did. This Silly computer though keeps throwing up an error with the program i am using (MPLAB IDE V8.83) starts. I am now starting to work on motors too.

My programs are being based on the Hotpoint WM64 we had - but instead of the tumbles when draining i will have mine to go to distribute at the start of drain, providing the pump works ok with it.

The WM64 We had was the best machine, until one day in 2005 when it ended up on the back of a skip lorry.

Chip diagram. I will be using a 24 pin chip.

 

[optima]

Logic

Well all is good, no leaks & it is now heating up to the correct temperature of 50,60 & 90deg. I have added one thing that just finishes it off & that is the classic red Hoover logo badge.

 

[electron1100]

Thermostats

Nice work well done ;-)..............another excellent machine saved

Gary

 

[optima]

Hoover

Cheers Gary

 

[hotpoint95622]

hotpoint 95622

Fantastic work, always gratifying when a problem is fixed and a machine returned to good health.

Lee

 

[optima]

Hoover

Yes it is Lee,

Two wash loads have been done in it today & it worked spot on & it washes far better than any new washer on sale these days.

 

[Maturasigma]

Wow, it looks so very great!!

I´ve had an Hoover ÖKO Logic WA1000 De Luxe, but i´ve must give it away, bt it was irreperable broken

at the moment is a Hoover ÖKO Logic WA1200 De Luxe in my near, but i think, that had an big problem too...

 

[zanussi_lover]

Lovely Machine

Hope you make videos of it, it looks fantastic =]

 

[optima]

Hope you make videos of it

Haha,

Zanussi lover. I'm still trying to get to grips with taking photo's on my camera & i'm not very good at that let alone making a video, but you have got me thinking because there is a video recording facility on my camera.

 

[optima]

Jamie,

Those Beko WM5100W washers are built really well, we have sold loads of them. Just a shame Beko didn't think of putting a time saver option button on them. Thank god for the 30 minute quick wash because if i was to tell a customer how long a standard 40d cotton cycle lasted they would run a mile.

 

[hooverzanmiele]

Red Hoover Badge

Hi Craig,

Did the hoover badge come with the machine? Or did you buy one?

If you bought it, can you direct me to where you invested in one? So I can get one for my Logic Premier.

Thanks.

CJ

 

[optima]

Hoover Badge

CJ,

I got the badge from work it accidentally fell off a new Hoover Washer/Dryer haha.

 

[hooverzanmiele]

Logic Model Number

Hi Craig,

Just been looking at my last Logic AutoWasher, it was an Aristocrat Logic 1300, model A3678, there are 02 vids of it on YT. I got it as a set with a Hotpoint Aquarius Ultima 1400 AutoWasher 9566, which's going to my Uncle soon, unfortunately the Aristocrat Logic went back to the shop as it wasn't running properly, but, after the fault issues with the Logic Premier when I first got it, I'd say the issue was the PCB board that'd become unfastened from the cabinet wall where they were positioned upon production.

I've attached a pic of it for you. Same model number as yours, just the number digits swapped round.

When I get a few spare minutes, I'll create a new thread with each page of the 03 different Hoover range brochures I've got, plus some of my pixel perfect replica's to go with.

I'll let you know when the thread's been created & the pics/replica's added to it.

CJ