Just got my first wringer washer, and it needs a little work so I need some help

[mstone]

I dont have the spanner wrench. It is not even in the parts diagram booklet weirdly enough. I tried PB blaster, and it is still sitting with some on it but I think I actually sprayed it in thw wrong place lol. So I wil try that again. I would just think I would get more leverage this way than with a flat metal object on its own.
Larry warned me not to remove that thrust bearing retainer also, but the manual says to just do it. I will have to read the putting it back together section to see what it says about that lol.

 

[mstone]

I dont have the spanner wrench. It is not even in the parts diagram booklet weirdly enough. I tried PB blaster, and it is still sitting with some on it but I think I actually sprayed it in thw wrong place lol. So I wil try that again. I would just think I would get more leverage this way than with a flat metal object on its own.
Larry warned me not to remove that thrust bearing retainer also, but the manual says to just do it. I will have to read the putting it back together section to see what it says about that lol.

 

[stan]

Maybe

Let the PB blaster soak for a day..then some heat.

 

[mstone]

I tried it again today, but still stuck. Will let the PB blaster sit. And heat? Hmm. I dont havw a torch so idk what I would use for that. I think tomorrow I will just try smacking it with a hammer! And if that doesnt work, I will try to cut the wheel in half with a dremel saw. I have no patience for that BS lol. Especially since the wheel is being replaced, and the stud comes with it. Also, those 4 gears add up to about $111 from Mark. I cant imagine a new power unit from him being much more than $180, in case I cant get it.

By the way, I got my box of parts from him!

Also, I looked in the manual about the thrust bearing retainer, and it sounds very easy to put back in and set the thrust. All you do is tighten it then back off barely, and then do it once more when the whole PU is put back together and installed.

 

[tinkr]

There's always one bolt

In every project. I was thinking heat also. I would think the gears are hardnend steel. Will a Dremel blade
cut that?
And in the past my experience , in the instructons it sounds so easy.
In actual life it's anything but.

Yea on the parts. Concentrate on something else and let the other soak.
At least you know your making progress.

 

[mstone]

It has been soaking all night so I will try it today.
It isnt a regular dremel tool with a small blade, is is specifically a dremel saw with a 4 or 5 inch diameter metal saw blade. Not sure if it will cut it, but I will try that if bashing it with a hammer doesnt work.
I guess there are a couple other things I could do while I wait.
And yeah, it is always harder than it sounds lol! Instructions: "Remove the stud for worm wheel by inserting the handle of a 38111 spanner wrench into the slot of the worm wheel stud and turn clockwise to unscrew."
There is no 38111 spanner wrench even in the parts catalog, and the thing does not want to move at all! So that means hammer time!

 

[mstone]

I put enough torque on that thing, that it twisted off the butt end of the drill bit in the socket.

 

[mstone]

Ok so I tried hammering on the stud, and it came off with the worm wheel. Problem is that it wont come off the worm wheel, no matter how much I hammer the stud, and the two together do not fit to come out of the power unit as a whole. The possibility of just getting a new power unit draws ever closer.

 

[mstone]

The dremel saw cut with ease but was not deep enough.

 

[stan]

New

Power Unit.. Sounds like a plan!
Can you get one? If you can and you get new one..maybe you can drop that one from a second floor! Wonder if that would break it loose! LOL

 

[mstone]

No not yet. I got to talk to Mark a bit more, and he convinced me not to buy one as they are around $280 from him, not counting shipping and tax. But again that is for a fresh power unit and center plate attached to it.
He suggested trying soaking the whole thing in solvent for a day, but I am gonna look for the router saw in the garage, and get a metal cutting blade for it and try to cut through the stud rather than the worm wheel and hope that works. And you would habe to drop it from 10 stories and smash up the housing to maybe come close to getting that wheel to come off. It may as well be one piece.

 

[mstone]

I bashed it with a hammer A LOT!

 

[stricklybojack]

.
Post more pics if you can.
I really want to see what's going on.

 

[mstone]

OMG! I finally got the worm wheel and stud out of the transmission. I had to cut the worm wheel into pieces and hammer and chisel at it. Evrn with a big chunk removed, it still would not come out, but here it is! Hopefully the housing isnt too badly damaged. Now it is on to the thrust bearing retainer, worm wheel, and shifter cam!

 

[mstone]

*Worm gear, not worm wheel.

 

[tinkr]

Perserverience

Pays off. Holy moley. Speechless.

 

[mstone]

Haha! Yes it does! Thank you! It took me days to decide to just go ahead and cut it up, and I had to get a thick metal cutting blade for pur sawzall, and use two metal cutting wheels on my dremel saw.

Now the thrust bearing retainer is stuck on and so is the thrust collar to the worm shaft. The shaft keeps turning so I cant really grip it. Will try using a piece of the worm wheel to lock teeth and hold it in place, but i still gotta gett of the retainer.
And the instructions are actually a bit wrong on this part.

 

[mstone]

UMM...

 

[mstone]

Ok i got it all out, just have to get the parts separated now.
Instructions "tap down on one end of the retainer to loosen it." But it does not do anything. Real life, hit the other end of the worm shaft with a hammer to poo it out.

 

[stan]

Can u

Get a new part for that broken one?
You doing really well with this! You've got the same deternanation that Larry had! And you have a great attitude
Your problems are a bit unique to your old gal, but thats they way if it..with these old girls
I'm staying tuned in!