Big Bertha Back In Good Health (Miele W 1070)

[hhsuds]

New Shocks for Bertha

Good day, curious to know if the replacement shocks were Miele OEM or a generic brand, and what the actual part number might be.
Miele Canada wants $212 for replacemnets for my W1926 part# 4828874

Thanks!

http://www.ebay.co.uk/itm/110553944414?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

 

[launderess]

Miele OEM

Didn't have time to wait for ordering "generic" or otherwise from Europe.

Also Miele warranties their parts for (90 days?) or such which sealed the deal on our end. Having watched that poor serviceman swap out the shocks on our washer am in no mood to have it done again anytime soon.

Being as this may from doing research on the matter many DIY persons in the EU and elsewhere seem to have on balance good experiences with "generic" shocks for many brand of washers, and that included Miele.

Genunie OEM Miele shocks *can* be cheaper if sourced from EU/UK, but much depends upon the exchange rate and shipping charges. Cheapest we found at the time was only about $50USD (more or less) cheaper than getting them from MieleUSA. Generics were cheaper but again you pays your money there and takes your chances.

 

[frigilux]

Launderess--- Does this photo look like the controls of a Miele w1070? Do you know the year yours was manufactured?

 

[launderess]

Yes, it tis our "Big Bertha" and have no idea of the exact year of her "birth".

There has been some considerable "lively" debate on how long the 10XX series was manufactured and sold for the USA market within the group. MieleUSA tells us that the models were replaced by the 19XX series starting around the early to mid 1990's, but who knows.

 

[launderess]

@hsuds

About those Miele shocks shown in link above; it is very important you match replacement shocks to what your model of machine. IIRC the shocks listed in your link are for the "Little Giant" model washers.

What I did was to contact Miele's parts department to obtain the proper part number for the shocks, then hunted around the Interent to see what there was.

Usually shocks for Miele washers will cover a series of models but what is important is which way they fit and matching the hole openings where the tub and bolts match up.

Oh and even though Miele sends new bolts/nuts with the shocks you may simply wish to reuse the one's you have and keep the new as spares. This is what our man did but don't know what one will do with the spare "nuts and bolts". *LOL*

 

[hhsuds]

Giant Shocks

Yes indeed the W1926 is a "Little Giant" albeit one of the earlier versions.
It weighs in at 227 lbs which is 15 lbs more than the recent PW5065.

I think it is a very close cousin of the WS5426 model which seems to be very hard to find on this side of the pond.

http://www.wetcleaning.com/pdf/Washer_spec.pdf

 

[launderess]

IIRC All The 19XX Series

Came in at about 227lbs. Just passed up at W1926 with matching dryer located just one state over. It was down by the Jersey Shore and with TS Irene just having hit that area wanted to go personally and examine the thing to see what one would be getting. Waited too long and the things are now gone. Story of my life! *LOL*

IIRC the W1926 and it's later cousin the W1986 were 6kg models based on the "Little Giant" Miele series. Recall also that the 12XX series was as well but later versions.

 

[hhsuds]

Correction

The W1926 really weighs in at 250lbs/114kg....this info is from both the owners and service manual. The new link I attached corrects it but reverses the washer and dryer weights. It is a monster to move!

http://www.wetcleaning.com/pdf/Wet-Cleaning-and-Laundry-Systems-Brochure.pdf

 

[launderess]

Wetcleaning

Can be done with most Miele washers from the 19XX series on, you just have to know what you're doing if the proper cycles aren't already in place.

IIRC the W1930 weighs 103kg which is about 227lbs.